Renaissance Machine / Magellan by G7 Solutions (04/27/2006) -------------------------------------------------------------------------- -------------------------------------------------------------------------- -------------------------------------------------------------------------- Mini-Mach-Chip.rud version: 1.3.8.8 (03/13/2006) -------------------------------------------------------------------------- -------------------------------------------------------------------------- -------------------------------------------------------------------------- Version 1.3.8.8, Mini1388, release It is based on Version 1.3.8.7, Mini1387, and it has some changes as following: 1.Solving the problem of MoveTable command(0x04 0x10) in repeat function. 2.Adding two key commands, which are DOG+TRIM, as to set half current of stepper DOG+ORG, as to go to center of soft limits DOG+100, as to clear soft limits(set to max) 3.Adding new PC command of setting the Soft-Limits, but it is not debugged. Dog+UP : to make machine speed up Dog+DOWN : to make machine speed down Dog+Right : to make change color automatically, while in sewing Dog+LEFT : to set function for moving hoop. Default or 4 sounds, means moving hoop along with checking limit including pattern's size. 3 sound, means moving hoop along with checking limit except pattern's size. Dog+ORG : go to center of soft limits Dog+100 : clears soft limits (set to max) Dog+START : to enter into machine testing mode Dog+Sissors : to set half current of stepper Dog+STOP : to enter into ISP mode DOG+TRIM : as to set half current of stepper DOG+Hoop : F functions 1 use up and down arrow key to select 2 Use start to set 3 Use stop to exit Feature set: F0 return to the center of moving range, and remember the position before moving(it will be used with F2) F1 Set the soft limit by P1 and P2, and along with remembering the position before moving(also concerned with F2) F2 restore to the position, which is ever remembered such as in F0, F1 or F3 mode. it is convenient to customer F3 while moving hoop by hand after power off, and power on again, this function will remember original position, and consider the current position as start position to continue embroidering. F4 Set the angle for hoop moving( such as H_) (for thickness of material) F5 Set the switch status of thread broken detection b1 ----- open the detection b0 ----- close the detection version 1.3.8.7, Mini1387, debug changing the some functions in trim working, and based on Version 1.3.8.6 some functions: 1.changed the last stitch for trimming making the last stitch to have firm_stitch function, and the length of firm_stitch is a half of last stitch 2.patch of some "F" functions, they are as following in detail F0 return to the center of moving range, and remember the position before moving(it will be used with F2) F1 Set the soft limit by P1 and P2, and along with remembering the position before moving(also concerned with F2) F3 while moving hoop by hand after power off, and power on again, this function will remember original position, and consider the current position as start position to continue embroidering. F2 restore to the position, which is ever remembered such as in F0, F1 or F3 mode. it is convenient to customer F4 Set the angle for hoop moving( such as H_) (for thickness of material) F5 Set the switch status of thread broken detection b1 ----- open the detection b0 ----- close the detection version 1.3.8.6, Mini1386, debug 1.changing the Max range in Y direction, from 400mm to 375mm 2.making the slow_start_speed at 150rpm, and relative picker control is changed 3.making the trimming in 2 stitches, and moving 1mm + 9mm to X right, then back to X left for 10mm Ver:--1.3.8.5 (01/31/2005) file name = Mini1385.rud Fixes: a Speed over ride b Move Paragraph after first stitch is sewn 1.while repeat sewing, machine will close tracing function after design sent by PC. 2.Opening the function of MOVE Key, also while in sewing. 3.setting the function by K_LEFT + K_DOG, which defines as: while alarming 2 times, means detecting the soft limit signal without including design's range. while alarming 4 times, means detecting the soft limit signal with including design's range. Version 1.3.8.4, Mini1384 1.fix the problem of high speed appearing while after a color changed. 2.fix the problem of Mini version, which using 1.3.X.X Ver:--1.3.8.3 (01/03/2005) 1 fix the problem in F0, F1 function Error code: 11 (MSPE) Main Shaft Position Error 12 Needle Position 15 Needle number too small 16 Needle number too large 17 Color Change time out 30-33 Limit error +x,-x, +y, -y respectively 35 hoop can not meet the x/y hard limits 37 start pos. of pattern is not aligned to fit soft hoop limits 40 no pattern in machine (Buffer) 50 Main Shaft Stalled Version 1.2.8.2, GF1282 original program for SG topdesk machine